- Manuals
- Brands
- Compaq Manuals
- Monitor
- QVision Graphics System
- Installation manual
15-17" tube monitors
Hide thumbs
-
- Contents
- Table of Contents
- Troubleshooting
- Bookmarks
Table of Contents
-
Table of Contents
- Chapter 1 INTRODUCTION
-
Product Features
-
- Chapter 2 STARTING up
-
Unpacking the Monitor
-
Connecting the Monitor to a Computer
-
Operating the Monitor
-
Pre-Set Modes
-
User-Modes
-
Storing Modes
-
Controls and Indicators
-
-
- Chapter 3 CARE and MAINTENANCE
-
Protecting the Monitor
-
Cleaning the Monitor
-
Shipping the Monitor
-
Servicing the Monitor
-
Troubleshooting
-
- Appendix A SPECIFICATIONS
-
Acceptable Signal Transmission Schemes
-
- Appendix B NATIONAL POWER CORD SET REQUIREMENTS
-
U.s. and Canada
-
Other Countries
-
- Appendix C ELECTROSTATIC DISCHARGE
-
Preventing Electrostatic Discharge
-
Methods of Grounding
-
Advertisement
Quick Links
Download this manual
QVision Operations and Installation Guide
NOTICE
The information in this guide is subject to change without notice.
COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR
TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED
HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE FURNISHING, PER FORMANCE, OR USE OF
THIS MATERIAL.
This guide contains information protected by copyright. No part of this guide
may be photocopied or reproduced in any form without prior written consent
from Compaq Computer Corporation.
®1992 Compaq Computer Corporation.
All rights reserved. Printed in the U.S.A.
COMPAQ, DESKPRO, SYSTEMPRO, LTE, FASTART
Registered U. S. Patent and Trademark Office.
SLT, EZ help and QVision are registered trademarks of Compaq Computer Corporation.
The software described in this guide is furnished under a license agreement or
nondisclosure agreement. The software may be used or copied only in
accordance with the terms of the agreement.
Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies.
QVISION GRAPHICS SYSTEM FROM COMPAQ
INSTALLATION AND OPERATIONS GUIDE
First Edition (February 1992)
Second Edition (April 1992)
Text Number 133577-002
Compaq Computer Corporation
Table ofContents
Advertisement
Table of Contents
Related Manuals for Compaq QVision Graphics System
-
Monitor Compaq COMPAQ Q1859 Quick Start Manual
Compaq computer monitor user manual (1 page)
-
Monitor Compaq Compaq Q2159 Quick Start
Optimum resolution 1920 x 1080, 60 hz (1 page)
-
Monitor Compaq Q2022a User Manual
(28 pages)
-
Monitor Compaq Q2009 - Compaq - Widescreen LCD Monitor Setup Poster
Setup poster q2009 lcd display (page 1) (1 page)
-
Monitor Compaq V50 User Manual
Color monitor (27 pages)
-
Monitor Compaq P110 User Manual
Color monitor (28 pages)
-
Monitor Compaq 303500-001 - V 900 - 19" CRT Display User Manual
User guide (28 pages)
-
Monitor Compaq 307713-001 - V 75 - 17" CRT Display User Manual
User guide (24 pages)
-
Monitor Compaq MV 540 User Manual
Color monitor (74 pages)
-
Monitor Compaq CRT Monitor s7500 Service Manual
Color monitor (34 pages)
-
Monitor Compaq TFT 1501 User Manual
15-inch lcd monitor (38 pages)
-
Monitor Compaq MV 740 User Manual
Color monitor (73 pages)
-
Monitor Compaq 7500 Series Reference Manual
Color monitors (36 pages)
-
Monitor Compaq Monitor TFT5015s User Manual
Flat panel monitor (31 pages)
-
Monitor Compaq V1100 User Manual
Color monitor (25 pages)
-
Monitor Compaq V55 User Manual
(22 pages)
Summary of Contents for Compaq QVision Graphics System
- Page 1 COMPAQ, DESKPRO, SYSTEMPRO, LTE, FASTART Registered U. S. Patent and Trademark Office. SLT, EZ help and QVision are registered trademarks of Compaq Computer Corporation. The software described in this guide is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of the agreement.
- Page 2 Consult the dealer or an experienced radio or television technician for help. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Compaq Computer Corporation may void the user's authority to operate the equipment. Cables...
-
Page 3: Table Of Contents
QVision Operations and Installation Guide vii, viii CONTENTS Chapter 1 INTRODUCTION Product Features Chapter 2 STARTING UP Unpacking the Monitor Connecting the Monitor to a Computer Operating the Monitor Pre-Set Modes ... -
Page 4: Introduction
QVision Operations and Installation Guide Chapter 1 INTRODUCTION The QVision Graphics System from Compaq is designed for easy installation and operation. To assist you while operating your monitor, this guide contains the following information: Chapter 1 Provides an introduction to the QVision Graphics System from Compaq. -
Page 5: Product Features
31 kHz to 58 kHz horizontal and 50 Hz to 100 Hz vertical. § The monitor cable connects to any VGA 15-pin type COMPAQ- compatible system. The monitor has 5 BNC inputs which, with the use of other cables, allow it to be used with almost any type of system. -
Page 6: Starting Up
QVision Operations and Installation Guide Chapter 2 STARTING UP This chapter gives instructions for removing the monitor from its packing material, connecting it to a COMPAQ personal computer, and using the operating controls. UNPACKING THE MONITOR WARNING: The monitor weighs approximately forty-five pounds. -
Page 7: Connecting The Monitor To A Computer
QVision Operations and Installation Guide CONNECTING THE MONITOR TO A COMPUTER To connect the monitor to your COMPAQ computer (or to any VGA-type 15-pin connector), follow these steps: Locate the power switch on the lower right side of the monitor face. - Page 8 QVision Operations and Installation Guide WARNING: To prevent possible damage to the video graphic controller board, both the computer and monitor must be OFF before connecting or disconnecting the signal cable. Power and Signal Cables Place the monitor in a convenient, well-ventilated location near your computer.
- Page 9 QVision Operations and Installation Guide Connect the 5 BNC connectors from the signal cable to the monitor. Push in and twist the connectors clockwise until they are locked into place. The BNC connectors are color-coded from left to right in the following order: White for horizontal sync (H) Black for vertical sync (V)
- Page 10 QVision Operations and Installation Guide Connect the other end of the signal cable to the 15-pin video graphics connector on the back of your computer. Connecting the Graphic Signal Cable to the 15-Pin Connector Secure the signal cable in place by tightening the screws on the connector by hand.
-
Page 11: Operating The Monitor
§ you are not using a COMPAQ standard graphics adapter § you are not using a pre-set mode (even with a COMPAQ graphics adapter) In these cases, you should re-adjust the size and centering of the monitor. It will automatically store the new setting as a user-mode. Then, the monitor will automatically recognize the new user-mode as it would a pre-set mode. -
Page 12: Storing Modes
QVision Operations and Installation Guide Storing Modes The monitor stores up to six user modes. When this limit is exceeded, the monitor replaces the first mode that was entered (first in, first out). Whenever you adjust the size and centering controls, these settings are stored in one of the following: §... -
Page 13: Controls And Indicators
QVision Operations and Installation Guide Controls and Indicators Controls and indicators are grouped along the lower front edge of the monitor. Each has only one function, indicated by the icon on its face. Controls and Indicators Adjustment Indicator The adjustment indicator provides information on whether an adjustment is being made or the limit of the adjustment range has been reached. - Page 14 QVision Operations and Installation Guide The following table lists the functions of each control:...
-
Page 15: Care And Maintenance
Chapter 3 CARE AND MAINTENANCE This chapter explains how to care for and maintain your QVision Graphics System from Compaq in normal everyday use. It also contains a troubleshooting guide. PROTECTING THE MONITOR To protect your monitor from overheating and other types of damage, follow these suggestions: §... -
Page 16: Cleaning The Monitor
QVision Operations and Installation Guide CLEANING THE MONITOR To clean the monitor follow these steps: Turn off the monitor and the computer. Dust the monitor by wiping the screen and the cabinet with a soft, clean cloth. If the screen requires more than dusting, use an anti-static CRT screen cleaner. -
Page 17: Servicing The Monitor
(such as overnight). If your monitor display is not functioning properly and you are unable to restore the normal display by adjusting the controls discussed in this guide, contact your Authorized COMPAQ Reseller or your Authorized COMPAQ Service Provider. -
Page 18: Troubleshooting
Missing color The BNC cables are Check BNC connectors. misconnected. Display not full Improper adjustments for Non-standard signals or too small horizontal or vertical size. may require special adjustments. Contact your Authorized COMPAQ Reseller or your Authorized COMPAQ Service Provider. -
Page 19: Specifications
QVision Operations and Installation Guide SPECIFICATIONS Specifications QVision Graphics System from Compaq Dimensions 15" 17" Height 16.6 in 39.9 cm 17.1 in 43.43 cm Depth 16.6 in 42.2 cm 17.4 in 44.29 cm Width 16.1 in 40.9 cm 17.9 in 45.46 cm... -
Page 20: Acceptable Signal Transmission Schemes
QVision Operations and Installation Guide The following input sync information is presented for technically sophisticated users who want to connect the monitor to a non-COMPAQ computer. You may need to provide your own cables or connectors to the computer. Non-technical users should consult an Authorized COMPAQ Reseller or an Authorized COMPAQ Service Provider. - Page 21 QVision Operations and Installation Guide Sync Signal Definition: Horizontal and vertical synchronization signals conform to the RS-343-A voltage level standards and use the normal horizontal input. Separate TTL Syncs, Separate Videos This scheme uses all 5 of the BNC connectors. Video Input Characteristic: Typical input impedance of the videoamps is 75 ohm.
-
Page 22: National Power Cord Set Requirements
QVision Operations and Installation Guide NATIONAL POWER CORD SET REQUIREMENTS Power cord set selection is determined by the following facts: The cord set must be approved for the country in which it is used. The appliance coupler (that is, the connector to the device itself, not the wall plug) must have a configuration for mating with a CEE22/IEC 320 appliance inlet (Standard Sheet C14). -
Page 23: Other Countries
The cord set must have a current capacity of at least 10 amperes and a nominal voltage rating of 125 or 250 VAC, as required by the specific country's power system. For more information about power cord set requirements, consult your Authorized COMPAQ Computer Reseller or your Authorized COMPAQ Service Provider. -
Page 24: Electrostatic Discharge
QVision Operations and Installation Guide Appendix C ELECTROSTATIC DISCHARGE A discharge of static electricity from a finger or other conductor may damage system boards or other static sensitive devices. This type of damage may reduce the life expectancy of the device. PREVENTING ELECTROSTATIC DAMAGE To prevent electrostatic damage, observe the following procedures:... -
Page 25: Methods Of Grounding
Use a portable field service kit with a folding static-dissipating work mat. IMPORTANT: For additional information on static electricity or assistance with the installation of this product, contact your Authorized COMPAQ Reseller or your Authorized COMPAQ Service Provider. ...
